Region specific anisotropy and rate dependence of Göttingen minipig brain tissue.

Traumatic brain injury is a major cause of morbidity in civilian as well as military populations. Computational simulations of injurious events are an important tool to understanding the biomechanics of brain injury and evaluating injury criteria and safety measures. However, these computational models are highly dependent on the material parameters used to represent the brain tissue. Reported material properties of tissue from the cerebrum and cerebellum remain poorly defined at high rates and with respect to anisotropy. In this work, brain tissue from the cerebrum and cerebellum of male Göttingen minipigs was tested in one of three directions relative to axon fibers in oscillatory simple shear over a large range of strain rates from 0.025 to 250 s-1. Brain tissue showed significant direction dependence in both regions, each with a single preferred loading direction. The tissue also showed strong rate dependence over the full range of rates considered. Transversely isotropic hyper-viscoelastic constitutive models were fit to experimental data using dynamic inverse finite element models to account for wave propagation observed at high strain rates. The fit constitutive models predicted the response in all directions well at rates below 100 s-1, after which they adequately predicted the initial two loading cycles, with the exception of the 250 s-1 rate, where models performed poorly. These constitutive models can be readily implemented in finite element packages and are suitable for simulation of both conventional and blast injury in porcine, especially Göttingen minipig, models.

Rate- and Region-Dependent Mechanical Properties of Göttingen Minipig Brain Tissue in Simple Shear and Unconfined Compression.

Traumatic brain injury (TBI), particularly from explosive blasts, is a major cause of casualties in modern military conflicts. Computational models are an important tool in understanding the underlying biomechanics of TBI but are highly dependent on the mechanical properties of soft tissue to produce accurate results. Reported material properties of brain tissue can vary by several orders of magnitude between studies, and no published set of material parameters exists for porcine brain tissue at strain rates relevant to blast. In this work, brain tissue from the brainstem, cerebellum, and cerebrum of freshly euthanized adolescent male Göttingen minipigs was tested in simple shear and unconfined compression at strain rates ranging from quasi-static (QS) to 300 s-1. Brain tissue showed significant strain rate stiffening in both shear and compression. Minimal differences were seen between different regions of the brain. Both hyperelastic and hyper-viscoelastic constitutive models were fit to experimental stress, considering data from either a single loading mode (unidirectional) or two loading modes together (bidirectional). The unidirectional hyper-viscoelastic models with an Ogden hyperelastic representation and a one-term Prony series best captured the response of brain tissue in all regions and rates. The bidirectional models were generally able to capture the response of the tissue in high-rate shear and all compression modes, but not the QS shear. Our constitutive models describe the first set of material parameters for porcine brain tissue relevant to loading modes and rates seen in blast injury.

A biomechanical-based approach to scale blast-induced molecular changes in the brain.

Animal studies provide valuable insights on how the interaction of blast waves with the head may injure the brain. However, there is no acceptable methodology to scale the findings from animals to humans. Here, we propose an experimental/computational approach to project observed blast-induced molecular changes in the rat brain to the human brain. Using a shock tube, we exposed rats to a range of blast overpressures (BOPs) and used a high-fidelity computational model of a rat head to correlate predicted biomechanical responses with measured changes in glial fibrillary acidic protein (GFAP) in rat brain tissues. Our analyses revealed correlates between model-predicted strain rate and measured GFAP changes in three brain regions. Using these correlates and a high-fidelity computational model of a human head, we determined the equivalent BOPs in rats and in humans that induced similar strain rates across the two species. We used the equivalent BOPs to project the measured GFAP changes in the rat brain to the human. Our results suggest that, relative to the rat, the human requires an exposure to a blast wave of a higher magnitude to elicit similar brain-tissue responses. Our proposed methodology could assist in the development of safety guidelines for blast exposure.

A 3-D virtual human model for simulating heat and cold stress.

In this study, we extended our previously developed anatomically detailed three-dimensional (3-D) thermoregulatory virtual human model for predicting heat stress to allow for predictions of heat and cold stress in one unified model. Starting with the modified Pennes bioheat transfer equation to estimate the spatiotemporal temperature distribution within the body as the underlying modeling structure, we developed a new formulation to characterize the spatial variation of blood temperature between body elements and within the limbs. We also implemented the means to represent heat generated from shivering and skin blood flow that apply to air exposure and water immersion. Then, we performed simulations and validated the model predictions with experimental data from nine studies, representing a wide range of heat- and cold-stress conditions in air and water and physical activities. We observed excellent agreement between model predictions and measured data, with average root mean squared errors of 0.2°C for core temperature, 0.9°C for mean skin temperature, and 27 W for heat from shivering. We found that a spatially varying blood temperature profile within the limbs was crucial to accurately predict core body temperature changes during very cold exposures. Our 3-D thermoregulatory virtual human model consistently predicted the body's thermal state accurately for each of the simulated hot and cold environmental conditions and exertional heat stress. As such, it serves as a reliable tool to assess whole body, localized tissue, and, potentially, organ-specific injury risks, helping develop injury prevention and mitigation strategies in a systematic and expeditious manner.NEW & NOTEWORTHY This work provides a new, unified modeling framework to accurately predict the human body's thermal response to both heat and cold stress caused by environmental conditions and exertional physical activity in one mathematical model. We show that this 3-D anatomically detailed model accurately predicts the spatiotemporal temperature distribution in the body under extreme conditions for exposures to air and water and could be used to help design medical interventions and countermeasures to prevent injuries.

A Strain Rate-Dependent Constitutive Model for Göttingen Minipig Cerebral Arteries.

Computational simulations of traumatic brain injury (TBI) are commonly used to advance understanding of the injury-pathology relationship, tissue damage thresholds, and design of protective equipment such as helmets. Both human and animal TBI models have developed substantially over recent decades, partially due to the inclusion of more detailed brain geometry and representation of tissues like cerebral blood vessels. Explicit incorporation of vessels dramatically affects local strain and enables researchers to investigate TBI-induced damage to the vasculature. While some studies have indicated that cerebral arteries are rate-dependent, no published experimentally based, rate-sensitive constitutive models of cerebral arteries exist. In this work, we characterize the mechanical properties of axially failed porcine arteries, both quasi-statically (0.01 s-1) and at high rate (>100 s-1), and propose a rate-sensitive model to fit the data. We find that the quasi-static and high-rate stress-stretch curves become significantly different (p < 0.05) above a stretch of 1.23. We additionally find a significant change in both failure stretch and stress as a result of strain rate. The stress-stretch curve is then modeled as a Holzapfel-Gasser-Ogden material, with a Prony series added to capture the effects of viscoelasticity. Ultimately, this paper demonstrates that rate dependence should be considered in the material properties of cerebral arteries undergoing high strain-rate deformations and provides a ready-to-use model for finite element implementation.

Cerebral Vasculature Influences Blast-Induced Biomechanical Responses of Human Brain Tissue.

Multiple finite-element (FE) models to predict the biomechanical responses in the human brain resulting from the interaction with blast waves have established the importance of including the brain-surface convolutions, the major cerebral veins, and using non-linear brain-tissue properties to improve model accuracy. We hypothesize that inclusion of a more detailed network of cerebral veins and arteries can further enhance the model-predicted biomechanical responses and help identify correlates of blast-induced brain injury. To more comprehensively capture the biomechanical responses of human brain tissues to blast-wave exposure, we coupled a three-dimensional (3-D) detailed-vasculature human-head FE model, previously validated for blunt impact, with a 3-D shock-tube FE model. Using the coupled model, we computed the biomechanical responses of a human head facing an incoming blast wave for blast overpressures (BOPs) equivalent to 68, 83, and 104 kPa. We validated our FE model, which includes the detailed network of cerebral veins and arteries, the gyri and the sulci, and hyper-viscoelastic brain-tissue properties, by comparing the model-predicted intracranial pressure (ICP) values with previously collected data from shock-tube experiments performed on cadaver heads. In addition, to quantify the influence of including a more comprehensive network of brain vessels, we compared the biomechanical responses of our detailed-vasculature model with those of a reduced-vasculature model and a no-vasculature model for the same blast-loading conditions. For the three BOPs, the predicted ICP values matched well with the experimental results in the frontal lobe, with peak-pressure differences of 4-11% and phase-shift differences of 9-13%. As expected, incorporating the detailed cerebral vasculature did not influence the ICP, however, it redistributed the peak brain-tissue strains by as much as 30% and yielded peak strain differences of up to 7%. When compared to existing reduced-vasculature FE models that only include the major cerebral veins, our high-fidelity model redistributed the brain-tissue strains in most of the brain, highlighting the importance of including a detailed cerebral vessel network in human-head FE models to more comprehensively account for the biomechanical responses induced by blast exposure.

Investigation of the direct and indirect mechanisms of primary blast insult to the brain.

The interaction of explosion-induced blast waves with the head (i.e., a direct mechanism) or with the torso (i.e., an indirect mechanism) presumably causes traumatic brain injury. However, the understanding of the potential role of each mechanism in causing this injury is still limited. To address this knowledge gap, we characterized the changes in the brain tissue of rats resulting from the direct and indirect mechanisms at 24 h following blast exposure. To this end, we conducted separate blast-wave exposures on rats in a shock tube at an incident overpressure of 130 kPa, while using whole-body, head-only, and torso-only configurations to delineate each mechanism. Then, we performed histopathological (silver staining) and immunohistochemical (GFAP, Iba-1, and NeuN staining) analyses to evaluate brain-tissue changes resulting from each mechanism. Compared to controls, our results showed no significant changes in torso-only-exposed rats. In contrast, we observed significant changes in whole-body-exposed (GFAP and silver staining) and head-only-exposed rats (silver staining). In addition, our analyses showed that a head-only exposure causes changes similar to those observed for a whole-body exposure, provided the exposure conditions are similar. In conclusion, our results suggest that the direct mechanism is the major contributor to blast-induced changes in brain tissues.

A 3-D virtual human thermoregulatory model to predict whole-body and organ-specific heat-stress responses.

OBJECTIVE: This study aimed at assessing the risks associated with human exposure to heat-stress conditions by predicting organ- and tissue-level heat-stress responses under different exertional activities, environmental conditions, and clothing. METHODS: In this study, we developed an anatomically detailed three-dimensional thermoregulatory finite element model of a 50th percentile U.S. male, to predict the spatiotemporal temperature distribution throughout the body. The model accounts for the major heat transfer and thermoregulatory mechanisms, and circadian-rhythm effects. We validated our model by comparing its temperature predictions of various organs (brain, liver, stomach, bladder, and esophagus), and muscles (vastus medialis and triceps brachii) under normal resting conditions (errors between 0.0 and 0.5 °C), and of rectum under different heat-stress conditions (errors between 0.1 and 0.3 °C), with experimental measurements from multiple studies. RESULTS: Our simulations showed that the rise in the rectal temperature was primarily driven by the activity level (~ 94%) and, to a much lesser extent, environmental conditions or clothing considered in our study. The peak temperature in the heart, liver, and kidney were consistently higher than in the rectum (by ~ 0.6 °C), and the entire heart and liver recorded higher temperatures than in the rectum, indicating that these organs may be more susceptible to heat injury. CONCLUSION: Our model can help assess the impact of exertional and environmental heat stressors at the organ level and, in the future, evaluate the efficacy of different whole-body or localized cooling strategies in preserving organ integrity.

Effects of body size and load carriage on lower-extremity biomechanical responses in healthy women.

BACKGROUND: Musculoskeletal injuries, such as stress fractures, are the single most important medical impediment to military readiness in the U.S. Army. While multiple studies have established race- and sex-based risks associated with a stress fracture, the role of certain physical characteristics, such as body size, on stress-fracture risk is less conclusive. METHODS: In this study, we investigated the effects of body size and load carriage on lower-extremity joint mechanics, tibial strain, and tibial stress-fracture risk in women. Using individualized musculoskeletal-finite-element-models of 21 women of short, medium, and tall statures (n = 7 in each group), we computed the joint mechanics and tibial strains while running on a treadmill at 3.0 m/s without and with a load of 11.3 or 22.7 kg. We also estimated the stress-fracture risk using a probabilistic model of bone damage, repair, and adaptation. RESULTS: Under all load conditions, the peak plantarflexion moment for tall women was higher than those in short women (p < 0.05). However, regardless of the load condition, we did not observe differences in the strains and the stress-fracture risk between the stature groups. When compared to the no-load condition, a 22.7-kg load increased the peak hip extension and flexion moments for all stature groups (p < 0.05). However, when compared to the no-load condition, the 22.7-kg load increased the strains and the stress-fracture risk in short and medium women (p < 0.05), but not in tall women. CONCLUSION: These results show that women of different statures adjust their gait mechanisms differently when running with external load. This study can educate the development of new strategies to help reduce the risk of musculoskeletal injuries in women while running with external load.

The importance of modeling the human cerebral vasculature in blunt trauma.

BACKGROUND: Multiple studies describing human head finite element (FE) models have established the importance of including the major cerebral vasculature to improve the accuracy of the model predictions. However, a more detailed network of cerebral vasculature, including the major veins and arteries as well as their branch vessels, can further enhance the model-predicted biomechanical responses and help identify correlates to observed blunt-induced brain injury. METHODS: We used an anatomically accurate three-dimensional geometry of a 50th percentile U.S. male head that included the skin, eyes, sinuses, spine, skull, brain, meninges, and a detailed network of cerebral vasculature to develop a high-fidelity model. We performed blunt trauma simulations and determined the intracranial pressure (ICP), the relative displacement (RD), the von Mises stress, and the maximum principal strain. We validated our detailed-vasculature model by comparing the model-predicted ICP and RD values with experimental measurements. To quantify the influence of including a more comprehensive network of brain vessels, we compared the biomechanical responses of our detailed-vasculature model with those of a reduced-vasculature model and a no-vasculature model. RESULTS: For an inclined frontal impact, the predicted ICP matched well with the experimental results in the fossa, frontal, parietal, and occipital lobes, with peak-pressure differences ranging from 2.4% to 9.4%. For a normal frontal impact, the predicted ICP matched the experimental results in the frontal lobe and lateral ventricle, with peak-pressure discrepancies equivalent to 1.9% and 22.3%, respectively. For an offset parietal impact, the model-predicted RD matched well with the experimental measurements, with peak RD differences of 27% and 24% in the right and left cerebral hemispheres, respectively. Incorporating the detailed cerebral vasculature did not influence the ICP but redistributed the brain-tissue stresses and strains by as much as 30%. In addition, our detailed-vasculature model predicted strain reductions by as much as 28% when compared to current reduced-vasculature FE models that only include the major cerebral vessels. CONCLUSIONS: Our study highlights the importance of including a detailed representation of the cerebral vasculature in FE models to more accurately estimate the biomechanical responses of the human brain to blunt impact.

Animal Orientation Affects Brain Biomechanical Responses to Blast-Wave Exposure.

In this study, we investigated how animal orientation within a shock tube influences the biomechanical responses of the brain and cerebral vasculature of a rat when exposed to a blast wave. Using three-dimensional finite element (FE) models, we computed the biomechanical responses when the rat was exposed to the same blast-wave overpressure (100 kPa) in a prone (P), vertical (V), or head-only (HO) orientation. We validated our model by comparing the model-predicted and the experimentally measured brain pressures at the lateral ventricle. For all three orientations, the maximum difference between the predicted and measured pressures was 11%. Animal orientation markedly influenced the predicted peak pressure at the anterior position along the midsagittal plane of the brain (P = 187 kPa; V = 119 kPa; and HO = 142 kPa). However, the relative differences in the predicted peak pressure between the orientations decreased at the medial (21%) and posterior (7%) positions. In contrast to the pressure, the peak strain in the prone orientation relative to the other orientations at the anterior, medial, and posterior positions was 40-88% lower. Similarly, at these positions, the cerebral vasculature strain in the prone orientation was lower than the strain in the other orientations. These results show that animal orientation in a shock tube influences the biomechanical responses of the brain and the cerebral vasculature of the rat, strongly suggesting that a direct comparison of changes in brain tissue observed from animals exposed at different orientations can lead to incorrect conclusions.

A 3-D Finite-Element Minipig Model to Assess Brain Biomechanical Responses to Blast Exposure.

Despite years of research, it is still unknown whether the interaction of explosion-induced blast waves with the head causes injury to the human brain. One way to fill this gap is to use animal models to establish "scaling laws" that project observed brain injuries in animals to humans. This requires laboratory experiments and high-fidelity mathematical models of the animal head to establish correlates between experimentally observed blast-induced brain injuries and model-predicted biomechanical responses. To this end, we performed laboratory experiments on Göttingen minipigs to develop and validate a three-dimensional (3-D) high-fidelity finite-element (FE) model of the minipig head. First, we performed laboratory experiments on Göttingen minipigs to obtain the geometry of the cerebral vasculature network and to characterize brain-tissue and vasculature material properties in response to high strain rates typical of blast exposures. Next, we used the detailed cerebral vasculature information and species-specific brain tissue and vasculature material properties to develop the 3-D high-fidelity FE model of the minipig head. Then, to validate the model predictions, we performed laboratory shock-tube experiments, where we exposed Göttingen minipigs to a blast overpressure of 210 kPa in a laboratory shock tube and compared brain pressures at two locations. We observed a good agreement between the model-predicted pressures and the experimental measurements, with differences in maximum pressure of less than 6%. Finally, to evaluate the influence of the cerebral vascular network on the biomechanical predictions, we performed simulations where we compared results of FE models with and without the vasculature. As expected, incorporation of the vasculature decreased brain strain but did not affect the predictions of brain pressure. However, we observed that inclusion of the cerebral vasculature in the model changed the strain distribution by as much as 100% in regions near the interface between the vasculature and the brain tissue, suggesting that the vasculature does not merely decrease the strain but causes drastic redistributions. This work will help establish correlates between observed brain injuries and predicted biomechanical responses in minipigs and facilitate the creation of scaling laws to infer potential injuries in the human brain due to exposure to blast waves.

Changes in Volumetric Bone Mineral Density Over 12 Months After a Tibial Bone Stress Injury Diagnosis: Implications for Return to Sports and Military Duty.

BACKGROUND: Bone stress injuries (BSIs) occur in up to 20% of runners and military personnel. Typically, after a period of unloading and gradual return to weightbearing activities, athletes return to unrestricted sports participation or military duty approximately 4 to 14 weeks after a BSI diagnosis, depending on the injury location and severity. However, the time course of the recovery of the bone's mechanical competence is not well-characterized, and reinjury rates are high. PURPOSE: To assess the bone microarchitecture and volumetric bone mineral density (vBMD) over 12 months after a tibial BSI diagnosis. STUDY DESIGN: Case-control study; Level of evidence, 3. METHODS: We enrolled 30 female athletes from the local community (aged 18-35 years) with a tibial BSI (grade ≥2 of 4 on magnetic resonance imaging) for this prospective observational study. Participants completed a baseline visit within 3 weeks of the diagnosis. At baseline and 6, 12, 24, and 52 weeks after the BSI diagnosis, we collected high-resolution peripheral quantitative computed tomography scans of the ultradistal tibia (4% of tibial length) of the injured and uninjured legs as well as pain and physical activity assessment findings. RESULTS: From baseline to 12 weeks after the diagnosis, total, trabecular, and cortical vBMD declined by 0.58% to 0.94% (P < .05 for all) in the injured leg. Total and trabecular vBMD also declined by 0.61% and 0.67%, respectively, in the uninjured leg (P < .05 for both). At 24 weeks, mean values for all bone parameters were nearly equivalent to baseline values, and by 52 weeks, several mean values had surpassed baseline values. Of the 30 participants, 10 incurred a subsequent BSI during the course of the study, and 1 of these 10 incurred 2 subsequent BSIs. Participants who suffered an additional BSI were younger and had a later age of menarche, a greater incidence of previous fractures, and lower serum parathyroid hormone levels (P < .05 for all). CONCLUSION: Bone density declined in both the injured and the uninjured legs and, on average, did not return to baseline for 3 to 6 months after a tibial BSI diagnosis. The observed time to the recovery of baseline vBMD, coupled with the high rate of recurrent BSIs, suggests that improved return-to-sports and military duty guidelines may be in order.

Injury Length and Arteriole Constriction Shape Clot Growth and Blood-Flow Acceleration in a Mouse Model of Thrombosis.

OBJECTIVE: Quantitative relationships between the extent of injury and thrombus formation in vivo are not well understood. Moreover, it has not been investigated how increased injury severity translates to blood-flow modulation. Here, we investigated interconnections between injury length, clot growth, and blood flow in a mouse model of laser-induced thrombosis. Approach and Results: Using intravital microscopy, we analyzed 59 clotting events collected from the cremaster arteriole of 14 adult mice. We regarded injury length as a measure of injury severity. The injury caused transient constriction upstream and downstream of the injury site resulting in a 50% reduction in arteriole diameter. The amount of platelet accumulation and fibrin formation did not depend on arteriole diameter or deformation but displayed an exponentially increasing dependence on injury length. The height of the platelet clot depended linearly on injury length and the arteriole diameter. Upstream arteriolar constriction correlated with delayed upstream velocity increase, which, in turn, determined downstream velocity. Before clot formation, flow velocity positively correlated with the arteriole diameter. After the onset of thrombus growth, flow velocity at the injury site negatively correlated with the arteriole diameter and with the size of the above-clot lumen. CONCLUSIONS: Injury severity increased platelet accumulation and fibrin formation in a persistently steep fashion and, together with arteriole diameter, defined clot height. Arterial constriction and clot formation were characterized by a dynamic change in the blood flow, associated with increased flow velocity.

Effects of load carriage on biomechanical variables associated with tibial stress fractures in running.

BACKGROUND: Military personnel are required to run while carrying heavy body-borne loads, which is suggested to increase their risk of tibial stress fracture. Research has retrospectively identified biomechanical variables associated with a history of tibial stress fracture in runners, however, the effect that load carriage has on these variables remains unknown. RESEARCH QUESTION: What are the effects of load carriage on running biomechanical variables associated with a history of tibial stress fracture? METHODS: Twenty-one women ran at 3.0 m/s on an instrumented treadmill in four load carriage conditions: 0, 4.5, 11.3, and 22.7 kg. Motion capture and ground reaction force data were collected. Dependent variables included average loading rate, peak absolute free moment, peak hip adduction, peak rearfoot eversion, and stride frequency. Linear mixed models were used to asses the effect of load carriage and body mass on dependent variables. RESULTS: A load x body mass interaction was observed for stride frequency only (p = 0.017). Stride frequency increased with load carriage of 22.7-kg, but lighter participants illustrated a greater change than heavier participants. Average loading rate (p < 0.001) and peak free moment (p = 0.015) were greater in the 22.7-kg condition, while peak rearfoot eversion (p ≤ 0.023) was greater in the 11.3- and 22.7-kg conditions, compared to the unloaded condition. Load carriage did not affect peak hip adduction (p = 0.67). SIGNIFICANCE: Participants adapted to heavy load carriage by increasing stride frequency. This was especially evident in lighter participants who increased stride frequency to a greater extent than heavier participants. Despite this adaptation, running with load carriage of ≥11.3-kg increased variables associated with a history of tibial stress fracture, which may be indicative of elevated stress fracture risk. However, the lack of concomitant change amongst variables as a function of load carriage may highlight the difficulty in assessing injury risk from a single measure of running biomechanics.

Does Blast Exposure to the Torso Cause a Blood Surge to the Brain?

The interaction of explosion-induced blast waves with the torso is suspected to contribute to brain injury. In this indirect mechanism, the wave-torso interaction is assumed to generate a blood surge, which ultimately reaches and damages the brain. However, this hypothesis has not been comprehensively and systematically investigated, and the potential role, if any, of the indirect mechanism in causing brain injury remains unclear. In this interdisciplinary study, we performed experiments and developed mathematical models to address this knowledge gap. First, we conducted blast-wave exposures of Sprague-Dawley rats in a shock tube at incident overpressures of 70 and 130 kPa, where we measured carotid-artery and brain pressures while limiting exposure to the torso. Then, we developed three-dimensional (3-D) fluid-structure interaction (FSI) models of the neck and cerebral vasculature and, using the measured carotid-artery pressures, performed simulations to predict mass flow rates and wall shear stresses in the cerebral vasculature. Finally, we developed a 3-D finite element (FE) model of the brain and used the FSI-computed vasculature pressures to drive the FE model to quantify the blast-exposure effects in the brain tissue. The measurements from the torso-only exposure experiments revealed marginal increases in the peak carotid-artery overpressures (from 13.1 to 28.9 kPa). Yet, relative to the blast-free, normotensive condition, the FSI simulations for the blast exposures predicted increases in the peak mass flow rate of up to 255% at the base of the brain and increases in the wall shear stress of up to 289% on the cerebral vasculature. In contrast, our simulations suggest that the effect of the indirect mechanism on the brain-tissue-strain response is negligible (<1%). In summary, our analyses show that the indirect mechanism causes a sudden and abundant stream of blood to rapidly propagate from the torso through the neck to the cerebral vasculature. This blood surge causes a considerable increase in the wall shear stresses in the brain vasculature network, which may lead to functional and structural effects on the cerebral veins and arteries, ultimately leading to vascular pathology. In contrast, our findings do not support the notion of strain-induced brain-tissue damage due to the indirect mechanism.

Individual Differences in Women During Walking Affect Tibial Response to Load Carriage: The Importance of Individualized Musculoskeletal Finite-Element Models.

Subject-specific features can contribute to the susceptibility of an individual to stress fracture. Here, we incorporated tibial morphology and material properties into a standard musculoskeletal finite-element (M/FE) model and investigated how load carriage influences joint kinetics and tibial mechanics in women. We obtained the morphology and material properties of the tibia from computed tomography images for women of three distinctly different heights, 1.51 m (short), 1.63 m (medium), and 1.75 m (tall), and developed individualized M/FE models for each. Then, we calculated joint and muscle forces, and subsequently, tibial stress/strain for each woman walking at 1.3 m/s under various load conditions (0, 11.3, or 22.7 kg). Among the subjects investigated, using individualized and standard M/FE models, the joint reaction forces (JRFs) differed by up to 4 (hip), 22 (knee), and 26% (ankle), and the 90th percentile von Mises stress by up to 30% (tall woman). Load carriage evoked distinct biomechanical responses, with a 22.7-kg load decreasing the peak hip JRF during late stance by ∼18% in the short woman, while increasing it by ∼39% in the other two women. It also increased peak knee and ankle JRFs by up to ∼48 (tall woman) and ∼36% (short woman). The same load increased the 90th percentile von Mises stress (and corresponding cumulative stress) by 31 (28), 22 (30), and 27% (32%) in the short, medium, and tall woman, respectively. Our findings highlight the critical role of individualized M/FE models to assess mechanical loading in different individuals performing the same physical activity.

Skeletal loading score is associated with bone microarchitecture in young adults.

Physical activity that involves high strain magnitudes and high rates of loading is reported to be most effective in eliciting an osteogenic bone response. Whether a history of participation in osteogenic activities during youth, as well as current participation in osteogenic activities, contributes to young adult bone microarchitecture and strength is unknown. PURPOSE: We determined the association between a new skeletal loading (SkL) score reflecting physical activity from age 11 to adulthood, the bone specific physical activity questionnaire (BPAQ) and bone microarchitecture in young Black and White men and women. METHODS: We conducted a cross-sectional study of young ([mean ±â€¯SD] 23.7 ±â€¯3.3 years) Black (n = 51 women, n = 31 men) and White (n = 50 women, n = 49 men) adults. Microarchitecture and estimated bone strength (by micro-finite element analysis) were assessed at the ultradistal tibia using high-resolution peripheral quantitative computed tomography (HR-pQCT). Physical activity questionnaires were administered and a SkL score was derived based on ground reaction force, rate of loading, frequency, duration, and life period of participation per activity from age 11 onwards. BPAQ score was also calculated. We used multiple linear regression to determine associations between both SkL score and BPAQ score and bone outcomes, adjusting for age, height, weight, sex, and race. RESULTS: We found that SkL score, which accounts for current and historical physical activity, was significantly associated with most cortical bone parameters at the tibia including area, area fraction, porosity, thickness, and tissue mineral density (R2 = 0.27-0.55, all p < 0.01). Further, trabecular thickness, separation, number, and bone mineral density (R2 = 0.22-0.32, all p < 0.01), as well as stiffness and failure load (R2 = 0.63-0.65, all p < 0.01), were associated with the SkL score. The BPAQ was also significantly associated with most bone parameters, but to a lesser degree than SkL score. CONCLUSION: These findings suggest that among young adults, greater amounts of osteogenic physical activity, as assessed by the SkL score and BPAQ are associated with improved bone microarchitecture and strength. With the potential to predict bone parameters in young adults, these scores may ultimately serve to identify those most vulnerable to fracture.

A 3-D Rat Brain Model for Blast-Wave Exposure: Effects of Brain Vasculature and Material Properties.

Exposure to blast waves is suspected to cause primary traumatic brain injury. However, existing finite-element (FE) models of the rat head lack the necessary fidelity to characterize the biomechanical responses in the brain due to blast exposure. They neglect to represent the cerebral vasculature, which increases brain stiffness, and lack the appropriate brain material properties characteristic of high strain rates observed in blast exposures. To address these limitations, we developed a high-fidelity three-dimensional FE model of a rat head. We explicitly represented the rat's cerebral vasculature and used high-strain-rate material properties of the rat brain. For a range of blast overpressures (100 to 230 kPa) the brain-pressure predictions matched experimental results and largely overlapped with and tracked the incident pressure-time profile. Incorporating the vasculature decreased the average peak strain in the cerebrum, cerebellum, and brainstem by 17, 33, and 18%, respectively. When compared with our model based on rat-brain properties, the use of human-brain properties in the FE model led to a three-fold reduction in the strain predictions. For simulations of blast exposure in rats, our findings suggest that representing cerebral vasculature and species-specific brain properties has a considerable influence in the resulting brain strain but not the pressure predictions.

Regional Changes in Density and Microarchitecture in the Ultradistal Tibia of Female Recruits After U.S. Army Basic Combat Training.

Musculoskeletal injuries, such as stress fracture, are responsible for over 10-million lost-duty days among U.S. Army Soldiers. During Basic Combat Training (BCT), an 8- to 10-week program that transforms civilians into Soldiers, women are four times more likely than men to sustain a stress fracture. In this work, we performed high-resolution peripheral quantitative computed tomography scans on the ultradistal tibia of 90 female recruits [age = 21.5 ± 3.3 (mean ± standard deviation) years] before the start of BCT and after 8 weeks into BCT. Then, we divided the scanned bone volume into four sectors-lateral, posterior, medial, and anterior-and computed the bone density and microarchitectural parameters in each of the four sectors pre- and post-BCT. We used linear mixed models to estimate the mean difference for bone density and microarchitectural parameters, while controlling for age, race, and pre-BCT body mass index. Our results revealed that the total volumetric bone mineral density, trabecular volumetric bone mineral density, and trabecular thickness increased (p < 0.05) in each of the four sectors. In addition, cortical thickness and trabecular bone volume/total volume increased in both medial and posterior sectors (p < 0.05). Overall, six and five out of nine parameters improved in the medial and posterior sectors, respectively, after BCT. In conclusion, the heightened physical activity during BCT led to the most beneficial bone adaptation in the medial and posterior sectors of the ultradistal tibia, which is indicative of higher loading in these sectors during activities performed in the course of BCT.